Clik here to view.
RE: SUDA Bug - Geometry rules are lost after making a utility line
  Robert GarrettSenior Software Consultant865-254-11403243 Fairview LaneStrawberry Plains, TN 37871Â
View ArticleSUDA Bug - Geometry rules are lost after making a utility line
See attached video.Create Geometry which includes snap rules. Â In the video it is simply two lines with the end snapped. Â But the same is true for all geometry snap rules.The geometry behaves correctly...
View ArticleClik here to view.
RE: SUDA Bug - when place a node on a conduit with split, the trench is...
  Robert GarrettSenior Software Consultant865-254-11403243 Fairview LaneStrawberry Plains, TN 37871Â
View ArticleSUDA Bug - when place a node on a conduit with split, the trench is turned off
See attached video which shows:A utility line exists and is modeled with a trenchAdd a node using the method "By Conduit With Split"After the node is placed, the trench has been turned off and must be...
View ArticleRE: Bentley Civil Standards for Benelux won't install
ok. I assume that you are admin on the machine. also, go to control panel > user accounts > user account control settings, set the bar to the lowest setting and...
View ArticleRE: Bentley Civil Standards for Benelux won't install
I have not full admin rights only to second bullet on UAC
View ArticleRE: Bentley Civil Standards for Benelux won't install
ok. that is your problem then. try it with admin and uac turned off. communities.bentley.com/.../125514
View ArticleClik here to view.
Bentley Civil Standards for Benelux won't install
Hi,I've installed Powercivil 08.11.09.878 and I cant Install Country kid.see imagePowerCivil for Benelux: pcir081109878en_nl.exe and cds081109845en_nl.msiUsing Windows 8.1Regards, Christiaan
View Article[OR] Is there an equivalent to Point Density Interval in Open Roads?
I have a Terrain element that is being driven by a corridor, but I have to add some linear breaklines manually where the corridor tools cannot work. In Ss2 and earlier, I would have added these as...
View ArticleSite Modeler object is not tying into surface
I've been trying to get a building surface to tie into an existing surface but no cut and fill slopes are showing up. In fact, I can't get any surface created outside of the shape itself. When I used...
View ArticleRE: Open Roads: Displaying Schematic data in profile.
Hi Mark, Further to your answer, I would like to know how to transfer the super elevation from Open Roads to MX roads? As we will use MX to display the super elevation schematic. Regards, Rohan
View ArticleRE: Open Roads: Displaying Schematic data in profile.
Hi Rohan, You will need to export the alignment and the corridor edges to which the superelevation is applied using the "Export To Native" option in the "General Geometry" task. This will export the...
View ArticleRE: Open Roads: Displaying Schematic data in profile.
Hi Amita, Thank you for the revert. It will be very helpful if you share the steps. Regards, Rohan
View ArticleRE: Open Roads: Displaying Schematic data in profile.
Hello Rohan, Please refer the video below which will show you exact steps about export corridor elements to Native. communities.bentley.com/.../28818.how-to-export-corridor-modelling-elements-to-native...
View ArticleRE: Open Roads: Displaying Schematic data in profile.
Here you go, there is a video already posted. Forgot!communities.bentley.com/.../22499.video-creating-openroads-geometry-and-exporting-the-same-to-native-mx
View ArticleRE: points
Hello Chetan, Could you please elaborate in more detail about the boundary around the model in MX Native so that we can provide you possible solution at the earliest ? Regards, Purva Lakde
View Article