Quantcast
Channel: OpenRoads | OpenSite Forum - Recent Threads
Browsing all 15087 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Cannot get template drop to map to end of corridor in a linear template

Hello,I'm trying to apply a linear template to a line, but for some reason, the template drop stops just short of the ends of the corridor.When applying the template, I've tried keypoint-snapping the...

View Article


RE: Profile Run with Subsurface Utilities

Please provide the dgnlib and the terrain.

View Article


RE: OpenRoads geometry toggle degree of curve broken

Well, no. I had not tried that. And that will indeed allow me to input the values. But there is still a problem as the behavior has changed since some time in the past. In past versions, simply type...

View Article

Image may be NSFW.
Clik here to view.

[OR] Surface Templates - Any Way to Have the Top Follow the Top, but Have the...

While Site Modeling, we sometimes need a Raised Concrete Area but the top edge must be offset from the base to get a Terrain Element / DTM from the model. If we try to apply a surface template to this,...

View Article

RE: [OR] TR? Traditional Tentative Snap Not Working as it Always Has

I tested this in the OpenRoads Designer EAP2 v10.00.01.23. I tested it on various different horizontal elements such as line between points, circle, and simple line to element. When I performed a...

View Article


RE: Profile Run with Subsurface Utilities

Hi Justin, Would you instead of what I requested above, send me another dgn where you see this same crash. It crashed for me to, but when I deleted one of your pipes it worked. I'd like to get another...

View Article

Profile Run with Subsurface Utilities

I am running version 08.11.09.878 on Power Inroads V8i.  Every time I try to create a "Profile Run" under the "Utility Model" tab in Project Explorer, Inroads crashes and shuts down.  I've tried...

View Article

Image may be NSFW.
Clik here to view.

RE: Cannot get template drop to map to end of corridor in a linear template

Your template is extending to the start/end of the line you associated it with, CURB_FL_CREF. The Point Control you have seeks another line called CL_CREF. This line does not extend to the start of the...

View Article


RE: [OR] TR? Traditional Tentative Snap Not Working as it Always Has

I hope we don't have to wait until ORD to see some of these fixes.

View Article


RE: [IR-SS2] Any way to get a report on a feature?

MaryB, you can very easily get a report of all of the vertices along the Feature by going to Surface > Feature > Feature Properties. Just select the Feature from the list window and go to List...

View Article

RE: Cannot get template drop to map to end of corridor in a linear template

On the first point, I see what you mean. Obviously, I hadn't looked hard enough at that. My bad. On the second, I hadn't tried setting the horizontal offset to zero, but I did use the horizontal point...

View Article

RE: [IR-SS2] Any way to get a report on a feature?

XML Reports? What "type" of report (Geometry, Station Offset, Surface, Point Validation, Etc.)? I have the barest grasp on XML reports - I don't find them intuitive at all. Feature Properties ->...

View Article

RE: [IR-SS2] Any way to get a report on a feature?

Clearance, Station Offset/Base should allow report on Features as related to an Alignment. One of those might not allow you to specify an interval, but I'm pretty sure the other two support it.

View Article


[IR-SS2] Any way to get a report on a feature?

More specifically, elevations at an interval along? Or elevations at vertices?I am trying to look at pavement elevations along the left side of the existing road. It seemed reasonable to me to Import a...

View Article

Image may be NSFW.
Clik here to view.

RE: Image Draping with XWMS

Sometimes a person can miss the obvious :(I was assuming that terrain from powercivil is a mesh. But it was not , so I dropped it into one and then I could go ahead a little in my task. Thank you for...

View Article


Image Draping with XWMS

Hi,I using PowerCivil SS4 version where I would like to use a SWMS file and drape it over the terrain.I followed the procedure mentioned in the enclosed document. Issue is, as soon as I switch the...

View Article

RE: Image Draping with XWMS

We can not see with your screenshot if you did every step that is described in your known document" Steps to Drape WMS Image Over a Mesh.docx" BTW: From where did you got this work flow description?

View Article


RE: Geopak cross section error: [There are no Cross Section Cell to process...]

Thanks Nico. I was able to get my cross sections to work again, too. I was having issues with one surface where I had updated the profile, but my surface wasn't up to date.

View Article

Geopak cross section error: [There are no Cross Section Cell to process...]

I recently made a minor tweak to an alignment design.  At this point I re-ran pattern lines and was going to re-run the existing ground cross sections when I received the following error message:...

View Article

RE: Civil Cell Information

Hi Purva, Could you possibly post the civil cell library again? The link is expired. Thank you very much!

View Article
Browsing all 15087 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>