RE: [OR] Is it possible to create a Profile with Gaps?
What about using the Microstation trim to element for the first surface, reproject the same surface and trim that for the end and then project the last surface and trim both ends of it. All you would...
View Article[OR] Is it possible to create a Profile with Gaps?
Can one create a Profile for a Civil Geometry Element that has a disjointed profile? Or can one Civil Geometry have two Profiles that are active?I am trying to do site grading and there are elements...
View ArticleRE: Error message "Drape boundary will intersect itself" when adding feature...
Added versions to my post. Thank you for the reminder, I always forget. I need to find if there is an auto signature block.
View ArticleRE: Image Draping with XWMS
Does your dgn Modell and the xwms has the same geo coordinate system?
View ArticleRE: Image Draping with XWMS
Yes.. it is.. as the image sits on top of the design. But as soon as I set the draping on, it goes off.
View ArticleRE: dynamic and static cross sections are different
Can someone try if is the error reproducible?
View ArticleRE: Image Draping with XWMS
As you are using PC SS4 please describe your work flow in detail
View ArticleImage Draping with XWMS
Hi,I using PowerCivil SS4 version where I would like to use a SWMS file and drape it over the terrain.I followed the procedure mentioned in the enclosed document. Issue is, as soon as I switch the...
View ArticleClik here to view.
RE: dynamic and static cross sections are different
Sorry for the delay. I loaded your DGN and XIN in InRoads 08.11.09.878 and it doesn't appear to have an issue with the static cross sections. Here is a screen capture of my sections which are...
View Articledynamic and static cross sections are different
Iroads SS4 08.11.09.790 (last czech). I connect a video where I do cross section both ways in the same place, but the cross section are different. Static cross section are incorrect, instead rendering...
View ArticleRE: [OR] Civil AccuDraw - Can I get a Profile Station from a Plan View?
Start a profile command with Civil Accudraw active and your profile view active. Then, tentative snap in plan view. The station value of the tentative point will be populated in the station value of...
View ArticleRE: GEOPAK Drainage - Can't graphically select ("Station DP") location when...
A defect has been filed for this issue. The defect number is 663586.
View ArticleRE: Export Complex Terrain
Hi Rick, Yes, it is possible to export a complex terrain to a DTM. I have gone through the process Appending terrains to a new complex terrain and then exporting to DTM. The DTM loads and displays...
View ArticleRE: Cannot get template drop to map to end of corridor in a linear template
Hi Joel, Your linear template should start/end from the line you are targeting for the linear template when you lock it to the start/end. Have you tried applying a different linear template to see if...
View ArticleClik here to view.
Cannot get template drop to map to end of corridor in a linear template
Hello,I'm trying to apply a linear template to a line, but for some reason, the template drop stops just short of the ends of the corridor.When applying the template, I've tried keypoint-snapping the...
View ArticleRE: [OR] Setting XML Report Default Format Options
Changing them in the Format Options browser, changes them in the registry for me. I had to refresh the registry to see the changes. I did the workflow listed above.
View ArticleRE: [OR] Setting XML Report Default Format Options
There must be some setting on my PC that is preventing this. I can change these settings over and over and as soon as I execute a command that opens a new Report Browser, they revert back to the...
View ArticleRE: Problem in triangulation
The Delete Triangle command is going to delete the triangulation between triangulatable points. The DTM still thinks the point at 0 elevation is a triangulatable point in the DTM so it doesn't just...
View Article