RE: Superelevation
The list of points comes up and I can assign them, it processes through the points, however it doesn’t apply the super to the lanes. I have the points tagged with superelevation flags in the templates,...
View ArticleRE: Superelevation
I've seen something like this myself. Unfortunately I don't recall exactly what the solution was. From memory, it may have been competing point controls, or it might have been a problem of multiple...
View ArticleRE: Elements Disappear when Zooming In
Creating the 2D drawing did work for me as well but in the process, I would lose over 40 saved views so I had to revert back to the former drawing. In doing this however, it made me think about the Z...
View ArticleElements Disappear when Zooming In
The following issue was submitted to Bentley Technical Support. This issue has been transferred to this forum so that the community can benefit from the troubleshooting techniques and resolution.As...
View ArticleRE: Rule Deactivation
We have the same issues. I do understand and like the rules…but…We create machine models so our output is concrete and asphalt, not paper. We need the ability to control. Automatic is nice…but… LANEDan...
View ArticleRE: Superelevation
I was wondering if it could be the other point controls for the sections, I will turn them off and see if that helps.
View ArticleRE: GEOPAK says I have no cross section cells to process with regards to...
I think you could uninstall your version and install 08.11.07.615. Let's see what that does.
View ArticleRE: GEOPAK says I have no cross section cells to process with regards to...
Actually I figured out what the problem was just forgot to post it on here. There was an existing gpk file in the folder I was referencing from the surveyors so that clutter was causing the issue. Once...
View ArticleClik here to view.
Proposed surface cannot be found when trying to label cross sections or run...
I am trying to label cross sections and run earthwork in SS4 and neither are working properly for me. In both cases I create the cross sections and when I change to the correct model and try to run...
View ArticleRE: Render Surface with different materials.
The feature definitions for components such as kerbs, pavement layers, earthworks slopes all have (or should/could have) materials assigned to them, so that you would get the above style display when...
View ArticleRE: Unable to open Tools Dialog box - unknown keyin
I've also had this issue since switching from SS3 to SS4 I believe.
View ArticleUnable to open Tools Dialog box - unknown keyin
Recently I tried using Power InRoads and with it, Descartes to use the Scale-able Terrain Model tools. I noticed the following messages in the message center: when the toolbox dialog bog failed to...
View ArticleRE: Similar as Autodesk Freestyle
Not sure what the program you mention did but maybe you can start with herewww.bentley.com/.../lumenrt
View ArticleClik here to view.
RE: Similar as Autodesk Freestyle
LumentR is a bit overkill for my need. I am only looking for something in 2d likw these examples
View ArticleSimilar as Autodesk Freestyle
HiAutodesk had once a program called Autodesk Freestyle, a really good software to create quick precentation of your project.Has Bentley something similar?RegardsSigfus
View ArticleRE: Key-in and Accept-(Left Buttom)Mouse problem
I filed this under Enhancement 652668: Surface > View Surface > Contours, ability to display contours at .001 interval.
View ArticleRE: Key-in and Accept-(Left Buttom)Mouse problem
I checked Dynamics after I zoom in a lot, move mouse to the custom elevation. 1. Could I find another option from OpenRoads to replace Pass through Contours ? 2. OpenRoads from Power Inroads V8-Ss4 can...
View ArticleRE: Proposed surface cannot be found when trying to label cross sections or...
Hi John, This may have something to do with the design stage your corridor is set to. I tested it with a design stage 7 - Final Linear Features, and the design surface did not appear (similar to your...
View ArticleInroads SUE conduit operational status
how can we select conduits/ pipes/ nodes in item sets based on the operational status?thanks
View Article