RE: Autocad Drawings is not valid created by MX Road V8i SS2
Please share your .dwg files so that I can test on it and provide you possible solution at the earliest. Regards, Purva Lakde
View ArticleRE: Autocad Drawings is not valid created by MX Road V8i SS2
(Please visit the site to view this file)
View ArticleRE: Autocad Drawings is not valid created by MX Road V8i SS2
Thank you for your response. I have tested .dwg file provided by you on my system and yes I could see error " Drawing file is not valid". I would suggest you or can you please confirm to us that the...
View ArticleRE: Autocad Drawings is not valid created by MX Road V8i SS2
We are using AutoCAD version 2015 and default value to save dwg. file in MX is 2007/2008/2009
View ArticleAutocad Drawings is not valid created by MX Road V8i SS2
I am trying to draw all layout in Autocad File for printing, but when I create Autocad Drawings using Draw>Edit Layout> with "Save as Separate Drawing". drawing generates but it did not open. A...
View ArticleRE: InRoads SS4 - inlet tops upside down and rotated
Jon, I converted my corridor to a terrain model and it the inlets work just fine now. Thanks for the help. Jason
View ArticleClik here to view.
RE: Cutting Cross Sections at Event Points (OpenRoads SS4)
I think you may mean the Horizontal and Vertical Cardinal points. If so you can find the check box on the Create Cross sections dialog under the controls...
View ArticleRE: Cutting Cross Sections at Event Points (OpenRoads SS4)
Thanks for the response. I'm aware that you can cut Horizontal and Cardinal points on the cross section. Here we are required to cut cross sections at every crossing structure and driveway location and...
View ArticleRE: Cutting Cross Sections at Event Points (OpenRoads SS4)
Then currently the only option is to place lines or linestrings at those locations and add those in under the custom option in the create cross section dialog. There is an enhancement submitted to...
View ArticleRE: Cutting Cross Sections at Event Points (OpenRoads SS4)
Okay thanks. I was afraid of that.
View ArticleCutting Cross Sections at Event Points (OpenRoads SS4)
I'm using OpenRoads SS4 08.11.09.872In SS2 we were able to add Event Points to our alignments. When Cross Sections were cut we could have a cross section cut at every event point. I've been told or I...
View ArticleRE: Descartes in InRoads - how do you load it?
Descartes can run with InRoads or GEOPAK, all you have to do is choose the Descartes user workspace in MicroStation when launching InRoads or GEOPAK.communities.bentley.com/.../92212
View ArticleDescartes in InRoads - how do you load it?
When you install Descartes with MicroStation SS3, it has a user workspace (ucf) and a shortcut to start MicroStation with it, which works fine (outside of ProjectWise).But when you install InRoads (SS2...
View ArticleRE: LINESTYLE FROM MASTER FILE DOESN'T MATCH WHEN ATTACHED TO A NEW FILE AND...
For clarification, you have a master DGN file with a particular linestyle and the survey is attached to this master dgn. Then you reference it into a different DGN which has the same linestyle listed...
View ArticleTenative gets stuck
I am using Power Geopak to create cross sections for export to HEC-RAS and noticed that the snap does not work properly when I start using the cross section tools, such as labeler or DP offset...
View ArticleClik here to view.
RE: Open Roads - Arc vs Chord definition - Spiral Curve Spiral Tool
Did you ever get an answer in regards DOC not being correctly calculated?I'm having the issue where the input from the file is not being correctly calculated in COGO.There is a difference between the...
View ArticleOpen Roads - Arc vs Chord definition - Spiral Curve Spiral Tool
I am having a little trouble understanding the way the Arc vs Chord definition setting should work during the use of the Spiral Curve Spiral tool. Below I have 2 scenarios that report different...
View ArticleRE: Tenative gets stuck
This post covers my own experience with snaps. communities.bentley.com/.../118712
View ArticleRE: Tenative gets stuck
Your observations are exactly what is hapenning to me. The difference is that I have been using SS3 for about a year and this is the first it has acted this way. I have recently been using Civil Tools...
View Article